Watch Nick as he explains one of the new improvements we made to our spouts. Contact us to get your new and improved spouts!

1-800-522-8874

The choice of replacement blades for your Kemper™, John Deere®, and New Holland® FI rotary corn heads can make a significant difference in performance and yield. Let's explore the three options available:

Standard Blades
Hard-Surfaced Blades with Tungsten Carbide Edge
Serrated Aggressive Blades
...

This special sensor stops the feed drive when rocks are detected. The Rock Stopper fits many makes and models (including pull types) as long as your machine has a working metal detector.

Kooima Ag is the exclusive USA distributor for this product! To find out more, or to purchase your rock stop...

This kit will help with opening the feed rolls wider. It will also help by closing spaces that corn could fall through. Watch to see Nolan explain the installation process with this kit.

K9000KIT: https://www.kooimaag.com/products/earlage-kit-2
K105729 RH Earlage Side Plate: https://www.kooima...

We offer a variety of different parts from feed rolls to blower bands, and many different models, including older cutters and pull types! We are always expanding our product lines! See what Cole has to say about our replacement parts to fit 900 and FP230 series New Holland® cutters.

Shop our lin...

Kooima Ag Sharpening Stone K56626: https://www.kooimaag.com/products/sharpening-stone-7

Shop our header parts here: https://www.kooimaag.com/products/forage-harvester-header-parts

The customer has seen a decrease in the time he has to mix each day because of these Kooima Ag products. Our carbide insert style serrated knives are long-lasting and have a more aggressive cutting edge. Here at Kooima Ag, we have your mixing solutions! Our knives are made right in our building...

Shop our Kernel Processor Rolls on our website https://www.kooimaag.com/ or call 1-800-522-8874.

KK90654 RH Section: https://www.kooimaag.com/products/intake-disc-weld-on-section-clockwise-rotation-right
KK90655 LH Section: https://www.kooimaag.com/products/intake-disc-weld-on-section-counterclockwise-rotation-left
KK4500CB Adjusting Bar Tool: https://www.kooimaag.com/products/kooima-adjusti...

When you are grinding ear corn, it can be a challenge to keep the feed rolls open wide enough to feed properly. On Claas® 497, 498, 499 & 502 series machines, the upper feed rolls are controlled by hydraulic cylinders to monitor the crop flow. When doing ear corn the cylinders are too tight even ...

On Claas® 497, 498, 499 & 502 series machines, the upper feed rolls are controlled by hydraulic cylinders to monitor the crop flow. When doing ear corn, the cylinders are too tight, even on the lowest setting. The cylinder pulls the ear corn down and does not allow it to reach the cutter drum. Ou...

Our new K494STOP Kit is just what you need when it comes to grinding ear corn with a 494 series Claas® forage harvester. This kit will help raise the feed rolls, allowing more room to feed in the earlage. To install, the process is straightforward and can be switched back just as easily. See the ...

We have 25-foot heads available for John Deere®, Claas®, and New Holland®. Check them out on our equipment page here: https://www.kooimaag.com/equipment

This adapter features an advanced crop flow system with an additional bottom intake roller, complementing the standard top roller. Specially engineered for higher horsepower harvesters and larger corn heads, the KFR920 delivers better cleanout, constant feeding, and increased harvesting speeds av...

Our single roll adapter did a nice 4.2 mph in the field, with our dual roll, we could get up to 6 mph in the same field/conditions. Our K00494 Single Roll adapter is ideal to use in 600 horsepower or less machines for a midsize operation. Our K00498 Dual Roll Adapter is made for higher horsepow...

Shop upper rear feed rolls here: https://www.kooimaag.com/products/upper-rear-feed-roll-7

If you put full complete round bales in your mixer wagon, this bale ripper kit results in less time processing the bale. We have seen consistent 15-20 minutes of mixing time shaved off of each bale, as the bale gets brought down into the knives faster. We have also seen less fuel and less wear an...

Not sure when you need to replace these teeth? Watch this video and find out! Get your harvester running to its potential this harvest season - don't let worn-out teeth slow you down.

Visit our website at: https://www.kooimaag.com/
Or call 800-522-8874.

Kooima Ag exclusive High Performance Serrated Insert Knives: These mixer knives use a solid carbide insert edge providing 2-3 times the cutting life of the blades over a standard tungsten coated steel edge. The additional, Kooima Ag patented serrated design, provides a more aggressive cut which ...

K385001 - Standard Serrated Knife that fits a Jay-Lor® and Penta™ mixer. The K385001 knife is a step up from the standard OEM knife with the addition of a serrated cutting edge to aggressively cut through tough, stemmy, or dry hay. Each knife is made in our Iowa plant using a high carbon base ma...

The K385070 Bale Slicer is a great product for farmers that are wanting to shorten hay particle length within the same amount of mixing time. This product is used for cutting livestock rations into smaller particles which helps with feeding. Included in the kit is the K385024BIT replacement knife...

The K9000 Dual Roll Adapter features an improved crop flow system with the addition of an extra intake roller on the bottom. Combined with the standard top intake roller, this adapter is specially designed for today's higher horsepower harvesters and larger corn heads, providing better cleanout a...

K385018HP knife will fit Art's Way™, Kirby™, Laird™, Meyer™, Peecon®, and Supreme™ vertical mixers.
https://www.kooimaag.com/products/large-mixer-knife-2?utm_source=youtube&utm_medium=video&utm_campaign=k21187hp-k385018hp

K21187HP knife will fit Patz® vertical mixers.
https://www.kooimaag.com/...